MarkPRODUCTS

English

Use accurate torque controls to improve quality! Case examples can be found in torque handbook 10

GLOBAL HOME
日本語English中文Deutsch
Wireless Data Transfer Torque Wrench

FDD-AD

Click Type Wireless Data Transfer Torque Wrench
TUD markingRoHS markingHead insert 10DHead insert 12DHead insert 15DHead insert 19DHead insert 22D

Tightening Torque Data Management

Preset

Judgment

Wireless

Tightening torque and angle data are transmitted automatically at the audible “Click!” moment. Precision Pass/Fail judgments ensure a higher level of tightening reliability.

Shown with interchangeable head QH15D connected to CSPFDD100N3×15D-AD

Shown with the M-FD wireless module and AC adaptor BA8 connected to the R-CM receiver.

Angle measurement begins at trigger torque, and then the torque angle (θ) data is transmitted wirelessly to the R-CM receiver at the audible “Click” moment.

The threshold value set on the R-CM is compared, and a Pass/Fail judgment is then made.

TRG: Trigger torque; TL: Lower limit torque; TH: Upper limit torque; ΘL: Lower limit angle; ΘH: Upper limit angle

* Letters on first line indicate torque judgment; on second line, angle judgment; displayed as L, O, and H.

Application

  • Tightening Torque Data Management
  • Pokayoke (tightening error-proof)
  • Detects two rounds of tightening to prevent this human error (Pokayoke).
  • Detects increased torque due to insufficient rotations from “biting (seizure)” during tightening.

Features

  • The tightening torque value obtained at the “Click” moment and the angle data are sent wirelessly. * The angle (θ) is that formed between the previously set trigger torque and the position at the “Click” moment.
  • Tightening torque data and angle data are judged by the R-CM receiver, and the result is displayed on the Pass/Fail LED on the FDD-AD.
  • Can prevent human errors (Pokayoke (error-proofing)) by detecting double tightening, and can detect torque increase in insufficient rotation angles caused by thread fouling during tightening.
  • Settings can be done easily using a computer. The setting software can be downloaded for free from the Tohnichi website. Use the RS232C cable to connect the setting controller (SB-FH2) to the computer, then send the settings wirelessly from SB-FH2 to the FD/FDD transmitter and the R-CM + M-FD receiver.
  • Marking torque wrench MQSPFDD-AD is equipped with the FD/FDD transmitter, which can be consulted during a later process or even after shipment that tightening was performed correctly. Can be custom-made after Tohnichi receives your order.
  • Tohnichi’s interchangeable head torque wrenches can be used with our interchange head lineup, which offers the best selection in the world, making these wrenches ideal for your work.
  • The FDD-AD series is compliant with ISO 6789:2017 starting January 2022. For more information, see the technical data “Initiatives for ISO 6789:2017” at the bottom of the screen.

Specifications

Model CSPFDD25N3-10N×10D-AD CSPFDD
25N3×10D-AD		 CSPFDD
50N3×12D-AD		 CSPFDD
50N3×15D-AD		 CSPFDD
100N3×15D-AD		 CSPFDD
140N3×15D-AD		 CSPFDD
200N3×19D-AD		 CSPFDD
280N3×22D-AD		  
 
Torque range
[N･m]		 Min ~ Max 2～10 5～25 10～50 20～100 30～140 40～200 40～280  
Hand force (P) at max. torque [N] 53.8 134.4 240.4 229.4 343.6 400.6 449.4 424.2  
Dimensions
[mm]		 Effective length L 186 208 218 291 349.5 445 660  
Overall length L’ 193 214 217 290 349 429 627  
Head Φd3 10 12 15 19 22  
Body m 23 29.5 33 40  
n 9.2 11.2 12.2 15  
Φd 15 20 21.7 27.2  
ΦD 29 34 27  
Approx. weight [kg] 0.32 0.46 0.65 0.77 1.2 1.65  
                    Torque Accuracy ±3%  
                       
Model Transmitter            
FDD-AD            
Angle measuring range 0～240°            
Angle accuracy ±2°＋1digit
（Angular velocity is 30°/s〜180°/s when the bolt turned to 90°）		            
LED lamps Blue: Angle judgment & torque value judgment both OK
Flashes Red: Transmission NG
Glows Red: Angle judgment or torque value judgment NG		            
           
           
LCD screen 3-digit torque display (+ angle display)
Unit display; battery charge level display (4 levels)		            
           
Operating keys Power switch, Test switch, Set switch            
Power source 2 AAA nickel metal hydride batteries or 2 AAA alkaline batteries            
Hours of continuous use Approx. 12 hours            
Other functions Auto-Zero; Auto Power Off (0 ~ 99 min)            
Frequency 2.4 GHz band (2.402 ~ 2.479 GHz; 1 MHz intervals; 78 types)            
Communication method Spread spectrum (frequency hopping)            
Modulation method GFSK            
Modulation speed 1Mbps            
Group Gr000～255            
ID 3 digits (000 ~ 999); 7 alphnumeric characters            
Antenna Chip antenna            
Transceiving distance Approx. 10 ~ 20 m (depends on radio wave environment)            
Operating temperature range 0 ~ 50°C 85%RH or less (No condensation）            
Notes

  • If you need a calibration certificate, please specify the set torque.

  • The calibration certificate specifies the FDD-AD operating torque, not the display torque on the transmitter display.

  • The display torque on the transmitter display must be calibrated against the operating torque. See the manual for instructions.

  • The FDD-AD conforms to wireless technical standards in Japan (TELEC), the U.S. (FCC), Canada (IC), Thailand (NTC), China (SRCC), Malaysia (SIRIM), Indonesia (SDPPI), Taiwan (NCC), the EU (CE), South Korea (KC), India (WPC), Russia (FSB), and Singapore (IMDA). (Information valid as of June 2021.) However, certain restrictions apply regarding export procedures to Indonesia (SDPPI), so please check with Tohnichi for more information. Can also be used in Mexico and Vietnam.

  • Japan's Measurement Law requires that the units of measure for products marketed and used in Japan be SI units, except for some specialized fields.

  • Products manufactured for the global market offer a selection of metric and American units of measure.

  • Verify the wireless standards and technical criteria used in the applicable country or region.

  • See the catalog for further information on the R-CM receiver.

  • The FDD-AD series is compliant with ISO 6789:2017 starting January 2022. Calibration Certificates will be different from older products.

 

Standard accessory

  • FD/FDD transmitter protection cover (FD-PCV): 1

  • Two AAA nickel metal hydride batteries. * Charger not included.

 

 

Dimensions

Expand dimensions
◆ How to order

This product is manufactured after the order is placed.

Please specify your set torque value at the time of placing the order.

[Example 1] CSPFDD50N3X12D-ADXT30N･m

[Example 2] CSPFDD25N3X10D-ADXT Free + R-FDSET-AC

* R-FDSET-AC is a set composed of wireless modules for FD/FDD, the R-CM receiver, and the BA-8R (AC adaptor).

 

◆ Things to remember when ordering

  • CSPFDD-AD is pre-set, so a tester is required to set torque.

　When ordering, please specify the torque values you intend to apply.

  • The R-FHD receiver or R-CM + M-FD is required to receive data transmitted from an FDD-AD.

  • The setting controller SB-FH2 or SB-FH256 is required to perform settings for FD/FDD. (You will also need a computer and the RS232C cable.)

 

 

Download

Product Catalog

Japanese English Chinese German

You must be a registered member to download the following files.

Registration
Manuals

Japanese English Chinese German

Software

Japanese English Chinese German

2D CAD (DXF)

Japanese English Chinese German

3D CAD (IGES)

Japanese English Chinese German

Parts List

Japanese English Chinese German

Online Part Search System

Japanese Worldwide

How to Use
Features of TOHNICHI Torque Wrench

Japanese English Chinese German

Special Torque Wrench

Japanese English Chinese German

Applying the correct force/Loosening tasks/Tightening left-handed bolts and screws

Japanese English Chinese German

[September 2024 Version] Tohnichi’s Torque Engineering Seminars, ready to provide positive results in the workplace right away.

Japanese English Chinese German

Differences between adjustable, preset and pre-lock torque wrenches

Japanese English Chinese German

Interchangeable Head Series for Tohnichi Interchangeable Head Torque Wrenches

Japanese English Chinese German

Technical Data
4. Tightening Reliability

Japanese English Chinese German

5. Selection of Tightening Tools

Japanese English Chinese German

6. Torque Tools are Measurement Equipment

Japanese English Chinese German

[September 2024 Version] Everything from torque controls to Tohnichi’s Tightening Guarantee System

Japanese English Chinese German

Torque Wrench Management and Loss Fees

Japanese English Chinese German

Initiatives for ISO 6789:2017

Japanese English Chinese German

Powered by Translations.com GlobalLink Web SoftwarePowered by GlobalLink Web